*

This is no a universal guide to wall mounting your TV, but this might be helpful, especially if the placement the your wall surface studs does no lend itself to proper mounting.

In this example, we space installing the following bracket and flat display television:

*
Digicom Flush wall Mount model # DC-A660 (for TV"s 37" to 80")
*
spicy Aquos LC52D64U 52-Inch 1080p LCD HDTV
*


*
The final wall-mounted environment is pictured above. The cables space run with a Wiremold chair rail an installed vertically (sold at residence Depot). also shown space the wall-mounted front speaker of ours 5.1 surround system. The facility channel speaker is mounted 1/2" far from the wall so the cables have the right to pass behind it.

*

The studs in our home are not all same spaced, as shown in the diagram (due come the framing of the greater set of home windows that room not shown).

You are watching: Tv mount doesn't line up with studs

This is not the cause of our problem. even if the studs were spaced at also 16" intervals, the relative placement provides it difficult to mount this bracket to the studs without modifying the bracket or the studs. Ideally, you want the facility of the TV to heat up v the empty space between 2 studs.

What happens once your TV wall surface mount parentheses doesn"t line up through your wall surface studs? The photo on the left reflects our wanted TV place (centered between two windows). The "wall side" that the mounting bracket is presented to scale. Over there is accurate no means to mountain this bracket directly to the studs. Either the TV would be off-center, or the bracket would be off-center, causing the 90-pound TV to not be supported properly. because that this bracket, the two vertical supports (which are bolted come the wall surface studs) slide along the horizontal bars, enabling for some versatility in placement, however not sufficient in this case.

There room two means to resolve this problem. The very first is to cut out a big section that drywall and install horizontal overcome braces (2x4s) between the studs, for this reason you have actually something to bolt the bracket to. This requires two braces on each side the the center stud, for a complete of 4 braces. If you space running cables through the wall to hide them, opportunities are you already have a lot of drywall work ahead the you, anyway, so this might be a more desirable solution. If you favor not come tear up the wall, then the systems on this web page is a much better choice, and also it"s easier and also less time consuming than reinforcing the studs inside the wall. This an approach basically extends the bracket so it deserve to be bolted to 3 adjacent wall surface studs. for our installation, we decided to usage a "wiremold" cable raceway, to run vertically, to hide our cables. Our wall surfaces are heavily textured, making drywall repair much more difficult. Also, running the cables with the wall requires the you download an AC outlet directly behind the TV since the provided AC cord should not be operation inside that the wall. In our case, this would have compelled a great deal of added drywall repair since we do not have any existing outlets listed below the TV mounting location. Click on the images below to enlarge them.

*

To fix our problem, we use two level pieces of stole long enough to span throughout three wall surface studs. The original bracket will then mount to this bars, which room well-supported by all three studs. We provided mild steel level bars from house Depot, measure up 48" lengthy x 1 1/4" broad by 1/8" thick. We only needed around 42" size , therefore we reduced off the extra size (partially-cut bar is shown).

*

To get started, you require to recognize three things: 1. Her intended TV location. 2. Just how your bracket mounts to her TV (this can influence the location and also spacing of the wall-facing part of the bracket). 3. The areas of your wall surface studs. We supplied a pencil to draw all of this info right on the wall, using a big metal ruler and a level. Note the centers the the studs, and mark the locations for the 6 anchor bolts. Because that the Digicom bracket, the upper row of holes is specifically 5 1/2" inches over the reduced row.

*

Your wall surface mount kit must be offered with heavy duty wall anchors, made come screw straight into the wood studs. The Digicom clip comes through 6 anchor screws, i m sorry is all we need. (Normally, you would usage 3 anchor screws to connect the vertical bracket piece to 2 wall surface studs. In ours case, we room using the anchors to attach each horizontal bar to three wall surface studs.) mark the stud anchor places on your flat bar and also drill the holes. The holes should be just large enough because that the object of the anchor screws to pass through.

*

Both level bars are shown here. Note that there space 5 holes in every bar. The 2nd and fourth holes are used to bolt the Digicom bracket come the bars (these are the countersunk holes stated below).

*

Here is a closer view.

*

To mountain the Digicom bracket come our bars, we use two sets of countersunk 1/4" bolts, with a length of 1/2" to 3/4". The top of these bolts will be versus the wall, v the subject protruding through the flat bars, encountering out away from the wall. (You will additionally need lock washers and nuts because that these bolts.) The horizontal spacing of this bolts might depend on just how the TV side of her bracket attaches come the TV. In our case, the bolt feet on the ago of the TV space close together (7 1/8" apart), so us spaced the wall-side support at a more comprehensive distance the 20" apart.

See more: Millennial International Is A Sponsor A Millennial Today, Sponsor A Millennial Today

*

I did not have actually the ideal bit because that cutting the bevel (countersink) right into the level bar because that the bolt heads. Ns improvised by making use of a 1/2" dome carbide burr on a dice grinder.

*

*

Some views of ours 1/4" bolt relaxing in the countersunk holes. If you space so inclinded, you have the right to weld the bolt heads to the flat bar to organize them in place and prevent them indigenous rotating. Ns did not bother law this.
*

*

You will probably want to repaint these flat bars, beginning with one etching, rust-blocking primer. The bars space usually coated with oil and dirt when you buy them, therefore clean them v a degreaser.

An abrasive decaying can aid remove any kind of surface oxidation and give the inside wall a better surface come adhere to. If you perform this step, clean the bars as soon as last time with a degreaser prior to using primer.

*

Back come the wall... currently that our holes space all drilled, use the bars as specific template because that drilling her stud anchor pilot holes, so the the anchors room sure to line up through the feet in her bars.

*

I provided an etching (rust-proof) primer and also white satin rust-resistant paint to match the wall. once the bars space painted, you have the right to mount them to the wall. You deserve to use masking ice on the earlier side that the bars to organize the 4 clip bolts in place.

*

Here is a closer view, showing the object of ours 1/4" bolts facing outward, and also the black anchor screws installed into the wall studs.

*

*

Secure the vertical sections of the bracket to the bars utilizing lockwashers and nuts.
*

Here we present the lower horizontal ring bar put through the upright "wall side" brackets, and the top horizontal bar placed through the upright "TV side" brackets. The "TV side" base bolt to the earlier of the TV. To hang the TV, just lift the TV over and let that slide down so the TV brackets hook on come the reduced horizontal bar.

*

Once the TV is mounted, two 6" flat pieces (not shown) lock the end of the upper and lower horizontal ring bars together. These space attached with 4 bolts, threaded into the ends of the bars. This renders it difficult to lift up on the TV or cause it to accidentally "un-hook" native the reduced bar.